While we have tried to present a summary of the essential information on this topic, you should be aware that other items, such as local regulations, may apply to you. Please read the disclaimer.
What You Need to Know
The Clean Water Act requires virtually every automotive salvage or recycling operator to obtain a stormwater permit (with very few exceptions to this rule). Therefore, if you own or operate an automotive salvage facility you are required to maintain a stormwater permit. Rain or snow falling on your property can pick up contaminants as it runs off, and can carry the contaminants through drainage systems directly into streams, rivers, and lakes. The term "stormwater" refers to this type of runoff.
Stormwater permits are required because stormwater that comes in contact with metals, oil and grease, used batteries and tires, and other materials common at automotive recycling facilities may cause pollution that can affect the local community's ability to swim and fish in lakes, rivers, and streams. For example, the mercury that still may be found in old automotive switches is toxic to humans and to the fish they may catch and eat. By taking some common sense actions under the stormwater permit to prevent stormwater contamination, you can provide your community with environmental benefits to compliment the value of recycling end-of-life vehicles.
In 1987, Congress mandated that "industrial" sites obtain stormwater permits through the National Pollutant Discharge Elimination System or NPDES program. In 1990, EPA defined "industrial" to include, among many other types of sites, "salvage yards and automotive [recyclers]." [Title 40 CFR 122.26(b)(14)(vi)].
What is NPDES?
The NPDES permit program addresses water pollution by regulating point sources that discharge pollutants to waters of the United States. EPA authorized state agencies to perform NPDES or stormwater permitting, administrative, and enforcement aspects of the program.
In Iowa, the stormwater program is administered by the Iowa Department of Natural Resources. The automotive recycling, dismantling, or salvage industry is covered under the National Pollutant Discharge Elimination System (NPDES) industrial general permit. General permits reduce the amount of time and paperwork involved in obtaining a stormwater permit.
A storm water pollution prevention plan (SWPPP) is required for all storm water permits. The plan must be completed prior to submitting the stormwater permit application known as the "Notice of Intent." The plan should be kept on-site at the facility or construction site that generates the storm water discharge.
To file a complete Notice of Intent you must provide the following items:
The completed Form 542-1415 entitled "Notice of Intent for NPDES Coverage Under General Permit". Please seehttp://www.iowadnr.com/water/stormwater/forms.html
Proof of Public notification from the two newspapers in the area with the highest circulation.
Iowa law requires dischargers to make public notice for seeking coverage under a general permit. The public notice must be published at least one day at your own expense in two different newspapers with the largest circulation in the area where the discharge is located.
When your Notice of Intent is sent to the IDNR, you MUST enclose a clipping of each public notice with the names of the newspaper and date published, or an affidavit from each newspaper with the clippings attached to demonstrate your public notification requirement. If both proofs of public notice are not included with your application, the storm water permit authorization will NOT be issued.
The applicant has the option of paying an annual permit fee or a multi-year permit fee.
annual permit fee $150
3-year permit fee $300
4-year permit fee $450
5-year permit fee $600
Your SWPPP must include a description of potential sources of stormwater pollution and measures and controls, including best management practices (BMPs) that will be implemented at your facility to prevent or minimize stormwater contamination. When developing the SWPPP, you must consider the use of certain BMPs that EPA and DNR consider applicable to specific areas such as vehicle dismantling/storage areas and fluids storage areas. However, you do not need to limit yourself to just these BMPs.
For more specific information on developing a Pollution Prevention Plan, visit the ECAR SWPPP fact sheet.
Exceptions. Under the conditional no exposure exclusion, operators of industrial facilities in any of the 11 categories of "storm water discharges associated with industrial activity," (except construction activities, which are addressed under the construction component of the NPDES Storm Water Program) have the opportunity to certify to a condition of "no exposure" if their industrial materials and operations are not exposed to storm water. As long as the condition of "no exposure" exists at a certified facility, the operator is excluded from NPDES industrial storm water permit requirements.
An inspector may check the facility for compliance with environmental regulations. Conducting a "self-audit" will identify and correct problems before they result in penalties.
Use the following list to audit your stormwater permit:
- Does your facility have a stormwater permit? Verify that your facility has a current stormwater permit issued by the Iowa DNR if your facility falls under the requirement.
- Has your facility developed and implemented a stormwater pollution prevention plan or SWPPP? Verify that a SWPPP has been prepared and is available on-site for inspection. Review the plan and verify that BMPs have been implemented. Note: If the facility is inspected, the SWPPP will be checked against all requirements in the permit. It is required that all SWPPPs be fully compliant with the permit.
- Does your facility have a stormwater monitoring program? Review your records to verify that visual observations and sampling have been performed.
Best Management Practices (BMPs)
Most regulations tell you what you have to do to be in compliance, but they don't explain how to do it. That's where "best management practices" come into play. BMPs are proven methods that help you to get into compliance and stay there. The following BMPs are recommended for stormwater pollution prevention.
The following is a list of BMPs for auto salvage facilities identified by EPA when the stormwater regulations were published:
Dismantling and vehicle maintenance:
- Drain all fluids from vehicles upon arrival at the site. Segregate the fluids and properly store or dispose of them.
- Maintain an organized inventory of materials used in the maintenance shop.
- Keep waste streams separate (i.e. waste oil and solvents). Non-hazardous substances that are contaminated with hazardous substances are considered a hazardous waste.
- Recycle antifreeze, gasoline, used oil, mineral spirits and solvents.
- Dispose of greasy rags, oil filters, air filters, batteries, spent coolants and degreasers properly.
- Label and track the recycling of waste material.
- Drain oil filters before disposal or recycling.
- Store cracked batteries in a nonleaking secondary container.
- Promptly transfer used fluids to the proper container.
- Do not pour liquid waste down floor drains, sinks or outdoor storm drains.
- Plug floor drains that are connected to the storm or sanitary sewer. If necessary, install a sump that is pumped regularly.
- Inspect the maintenance area regularly for proper implementation of control measures.
- Filter stormwater discharges with devices such as oil-water separators.
- Train employees on proper waste control and disposal procedures.
Outdoor vehicle, equipment and parts storage:
- Use drip pans under all vehicles and equipment waiting for maintenance and during maintenance.
- Store batteries on impervious surfaces. Curb, dike or berm this area.
- Confine storage of parts, equipment and vehicles to designated areas.
- Cover all storage areas with permanent cover (roof) or temporary cover (canvas tarps).
- Inspect the storage yard for drip pans and other problems regularly.
Vehicle, equipment and parts washing areas:
- Avoid washing parts or equipment outside.
- Use phosphate-free biodegradable detergents.
- Consider using detergent-based or water-based cleaning systems in place of organic solvent degreasers.
- Designate an area for cleaning activities.
- Contain steam cleaning washwaters or discharge under an applicable NPDES permit.
- Ensure that washwaters drain well, and are not draining into a MS4 or surface water body.
- Do not discharge wastewater into a dry well.
- All discharges authorized by the general stormwater permit must fully meet all applicable water quality standards.
- Inspect cleaning area regularly.
- Install curbing, berms or dikes around cleaning areas.
- Liquid storage in above ground containers:
- Maintain good integrity of all storage containers.
- Install safeguards (such as berms) against accidental releases in the storage area.
- Inspect storage tanks to detect potential leaks. Perform preventative maintenance.
- Inspect piping systems for failures or leaks.
- Train employees on proper filling and transfer procedures.
Improper connection with storm sewers:
- Plug all floor drains if it is unknown whether the connection is to storm sewer or sanitary sewer. Alternatively, install a sump that is pumped regularly.
- Update facility schematics to accurately reflect all plumbing connections.
- Install a safeguard against vehicle washwaters and parts cleaning water entering the storm sewer unless permitted.
- Maintain and inspect the integrity of all underground storage tanks; replace when necessary.
Related ECAR Fact Sheets