ECAR Fact Sheet for South Dakota
Solvent Cleaning

Regulations
Self-Audit Checklist
Best Management Practices
Contacts
Related ECAR Fact Sheets
Other Relevant Resources

BACK to VIRTUAL TOUR

What You Need to Know

Various methods are used to clean oil and grease from auto parts before sale. This fact sheet covers the environmental issues associated with solvent cleaning methods such as parts washers containing mineral spirits. Aqueous cleaning (e.g., pressure washers, enclosed spray washers, steam cleaning) is covered under a separate fact sheet.

Used solvents are often the largest hazardous waste stream created by automotive recyclers. Used solvents can be harmful to workers and the environment because they are toxic and they emit dangerous vapors. In addition, solvent parts washers use cleaning solutions that eventually become spent and must be disposed of.

Regulations

The regulations that apply to spent parts-washer solvents are similar from state, meaning that spent solvents are considered a hazardous waste if they are an EPA-listed hazardous waste, or if they are a characteristic hazardous waste with a flash point less than 140 degrees Fahrenheit or have a toxic metals concentration above regulatory levels. In most cases, your used solvents will fall into one of these categories.

Waste solvents must be stored in containers that are in good condition and made of materials or lined with materials that are compatible with the stored wastes. The container must always be closed during storage, except when it is necessary to add or remove wastes. It also cannot be opened, handled, or stored in a manner that may cause it to rupture or leak. Containers holding hazardous waste must be clearly marked with the words “Hazardous Waste” and managed as such. See the ECAR Hazardous Waste fact sheet for more information.

The following are some of the common spent halogenated and non-halogenated solvents used in degreasing operations that are considered hazardous:

• 1,1,1-trichloroethane
• Acetone
• Benzene
• Carbon tetrachloride
• Chlorinated fluorocarbons
• Isobutanol
• Low flash point mineral spirits
• Methanol
• Methylene chloride
• Methyl ethyl ketone (MEK)
• Methyl isobutyl ketone (MIBK)
• Ortho-dichlorobenzene
• Tetracholoroethylene
• Toluene
• Trichloroflueoromethane
• Xylene

In addition to the solvents used, the parts washing systems generate sludge, which is usually hazardous because it contains toxic metals and solvents from the parts cleaned. Store all sludges from tanks in a closed and properly labeled (such as “WASTE SLUDGE”) container. Rags used to wipe parts off after being washed are also hazardous if they contain toxic metals at concentrations exceeding regulatory limits or listed hazardous solvents. See the ECAR Shop Towels fact sheet.

Many parts washers use filters that must be periodically changed. You need to determine if your used filters are hazardous by using the same process you used to determine if your solvent is hazardous.

Links to the Regulations. Use the following links to view the regulations pertaining to solvent cleaning processes.

South Dakota’s Hazardous Waste Management Rules (references federal hazardous waste regulations)

Federal EPA Standards Applicable to Generators of Hazardous Waste

Self-Audit Checklist

When an inspector comes to your facility, there are certain things he or she checks to see if you are in compliance with environmental regulations. It makes good sense for you to perform a "self-audit" and catch and correct problems before they result in penalties. Also, there are some compliance incentives associated with self-audits (see Audit Policy Page).

Use the following list to audit your solvent cleaning operations.

1. Are spent solvents stored in drums, tanks or other containers that are in good condition? Open containers, and rusting or leaking containers cannot be used for spent solvent storage.
2. Are solvent storage containers and tanks properly labeled? All used solvent storage containers must be labeled "hazardous waste."
3. Is the area around the solvent storage containers free of releases? Releases must be stopped and the released material cleaned up and managed properly.
4. Is spent solvent transported to a recovery facility by a certified transporter? Check your records and verify that all shipments of spent solvent were removed from your property by a state certified transporter.

Best Management Practices (BMPs)

Most regulations tell you what you have to do to be in compliance, but they don’t explain how to do it. That’s where "best management practices" come into play. BMPs are proven methods that help you to get into compliance and stay there. The following BMPs are recommended for solvent cleaning.

• Wipe off parts with a rag or wire brush before soaking in parts washer.
• Do not clean parts unnecessarily.
• Reduce the quantity of solvent used by implementing a two-stage cleaning system. The first stage should clean the dirtiest parts. The second stage uses cleaner solvent for final cleaning and rinsing. When the cleaning solution in the second stage is no longer effective, it can then be used to replace the solvent in the first stage. Fresh solvent is then used to replace the second stage.
• Parts washers should have a recirculating feature with built-in filtration to continuously remove dirt and contaminants. This will extend the life of the solvent.
• Drip racks or trays can help increase drainage from parts to minimize solvent loss.
• When not in use, solvent streams should be turned off and lids on parts washers should be kept closed to reduce evaporative solvent loss.
• Do not dispose of used solvent on the ground or in a storm drain.
• Do not combine spent solvent with used oil.
• Consider using a less hazardous solvent cleaner such as a citrus-based cleaner.
• Carefully review Material Safety Data Sheets (MSDS) to avoid hazardous materials whenever possible.
• Keep cleaning container closed when not in use to avoid evaporation, spills, fires and explosive hazards.
• Contract with a solvent management company to supply and recycle solvent.
• Keep accurate records of solvent, wash water, sludge processing and disposal for 3 years.

Contacts

1. For more information, contact the South Dakota Department of Environment and Natural Resources (DENR), Waste Management Program at 605-773-3153.
2. To report a spill or leak, call the DENR at 605-773-3296. To report the release after hours, on weekends or holidays, call State Radio Communications at 605-773-3231. DENR recommends that spills also be reported to the National Response Center at 800-424-8802. You can get more information from the DENR Spill Response Website.
3. To report an environmental incident or complaint, contact the nearest regional office.

Related ECAR Fact Sheets

1. Hazardous Waste
2. Aqueous Cleaning

Other Relevant Resources

1. South Dakota Antifreeze Recyclers

BACK to VIRTUAL TOUR